Find with reference code or description
Or search by measurements (mm)
FREE UK MAINLAND DELIVERY ON ORDERS OVER £100
Bearing King 1008 Taper Bushes 1008-5/8 Taper Locking Bush 5/8 inch Bore

1008-5/8 Taper Locking Bush 5/8 inch Bore

BKL Brand
1008-5/8 Taper Locking Bush 5/8 inch Bore
1008-5/8 Taper Locking Bush 5/8 inch Bore
In Stock
Taper lock bush suitable for pulleys and sprockets in the 1008 series
£4.94 INC.VAT
£4.12 EXC.VAT
Dimensions - d (inside diameter)15.88mm

Taper lock bush suitable for pulleys and sprockets in the 1008 series

Taper bushes are the most convenient and cost effective method of fixing components to a mating shaft without using any special tools. Taper bushes are pre-machined with the required bore & keyway size and are supplied complete with locking set screws, thus making savings in time and cost on any machining process.

Bore dia: 5/8 inch
Keyway width: 3/16 inch
Keyway depth: 0.09mm
Shallow keyway depth: -

Screw tightening torque (Nm): 5.6
Screw size (BSW): 1/4 inch, hex, socket size: 3mm

Large end dia: 35.0mm
Bush length: 22.3mm

Mass: 0.1kg

To Install:
1. Clean shaft, bore and outside of bush, and bore of hub. Remove any oil, laquer or dirt, Place bush in hub and match half holes to make complete holes (each complete hole will be threaded on one side only).
2. Lightly oil thread and point of set screws, or thread and under head of cap screws. Place screws loosely in holes that are threaded on hub side.
3. Make sure bush is free in hub. slip assembly onto shaft and locate in the desired position.
4. Tighten screws alternately and evenly until all are pulled up tightly
5. Hammer against large end of bush using hammer and block or sleeve to avoid damage. Screws can now be turned a little more to the specified torque setting. repeat this alternate hammering and screw re-tightening until the specified torque is reached. Fill all holes with grease to exclude dirt.

To Remove:
1. Remove all screws. Lightly oil thread and point of set screws, or thread and under head of cap screws.
2. Insert screws into removed holes that are threaded on the bush side. In sizes where washers are found under screw heads, be sure to use the washers.
3. Tighten screws alternately until bush is loosened in the hub and then remove the complete assembly. If bush does not loosen immediately, tap on hub.

1008-5/8 Taper Locking Bush 5/8 inch Bore image 2

BKL BrandBearing King offer a full range of BKL Brand products including ball, self-aligning, angular contact, cylindrical, needle and spherical bearings at highly competitive prices which are available for same or next day delivery

Related products Similar to 1008-5/8 Taper Locking Bush 5/8 inch Bore

1008-22 Taper Locking Bush 22mm Bore
BKL Brand
1008-22 Taper Locking Bush 22mm Bore
Taper lock bush suitable for pulleys and sprockets in the 1008 series
Price Breaks / More Information
1008-9 Taper Locking Bush 9mm Bore
BKL Brand
1008-9 Taper Locking Bush 9mm Bore
Taper lock bush suitable for pulleys and sprockets in the 1008 series
Price Breaks / More Information
1008-1/2 Taper Locking Bush 1/2 inch Bore
BKL Brand
1008-1/2 Taper Locking Bush 1/2 inch Bore
Taper lock bush suitable for pulleys and sprockets in the 1008 series
Price Breaks / More Information
1008-19 Taper Locking Bush 19mm Bore
BKL Brand
1008-19 Taper Locking Bush 19mm Bore
Taper lock bush suitable for pulleys and sprockets in the 1008 series
Price Breaks / More Information