Telephone: +44 (0)1709 527 269
Opening Hours: Monday to Friday (8.30am - 5.00pm)
Search

Reference Code


Search by size

mm
mm
mm

Use metric measurements only. See conversion chart.


Still can't find the part?

If you still can't find the part you need, contact us and we'll do all we can to locate it - just give us a call:
+44 (0)1709 527 269


Browse by category...

K-2030-10+ Kukko Universal 2-Jaw and 3-Jaw Puller Set with Quick-Adjusting Pulling Jaws

K-2030-10+ Kukko Universal 2-Jaw and 3-Jaw Puller Set with Quick-Adjusting Pulling Jaws
K-2030-10+ Kukko In Stock
£426.27£511.52 inc. VATGBP £ | EUR € | USD $
x

For removing bearings, gears, discs, etc.

Description
8 in 1 kit in the tried-and-tested KUKKO-L-Boxx-System.
The set facilitates the assembly of eight different pulling device models through the combination of pulling jaws and extensions.
Flexibility assured thanks to two-arm or three-arm design.
If there is adequate free space around the part to be removed, we recommend using a 3-jaw puller.
Standard pulling hooks in various lengths with quick adjusting capability quick adjust.
Pulling hooks with infinitely variable adjustment on the cross-beam.
Short and long mechanical pressure screws.
Milled thread treated with special coating.
Parallel pulling hooks in every position, even with full load.
Instructions on the cover.
Personal KUKKO-Chip-Code.

Advantage
Practical package for universal use.
Variable reach thanks to optional jaw extensions.
Can be installed on various pulling hooks.
Turning the pulling hooks enables them to be used both internally and externally.
Suitable for pulling asymmetric workpieces.
2-jaw cross-beam with hexagonal profile for good grip.
Spindle head band prevents the wrench from slipping off.
Almost all components available as replacement parts, time-saving order process thanks to numbering system.
Note: Pressure pads from series 600-17 are a good addition if the shaft is hollow and the spindle cannot be supported.
Stability support from optional series 219 clamp.
Complete easy-to-manage package.
KUKKO-L-Boxx-System compatible with systems by all common manufacturers.

Content

20-10+ Universal 2-jaw puller with quick adjusting jaws
30-10-T Cross-beam
614250 Mechanical pressure spindle.
1-92-E Jaws, individual
1-192-S 3 quick adjusting jaws (set)
1-252-S 3 quick adjusting jaws (set)

How it Works
The part due to be removed (e.g. a gear, pulley or ball bearing) is gripped from the outside. Tightening of the pressure screw and the resulting pressure removes the part from the shaft.
The puller must be positioned centrally for centre shafts. If the shaft is not sitting centrally, the parts can be removed asymmetrically with pullers with parallel pulling hooks.

Safety Information
The pulling hooks' sliding parts must always sit stably and fully on the cross-beam.
If several parts have to be removed, always follow a step-by-step process. Do not remove several parts at the same time.
The pulling hooks' support surfaces must always be straight and sit fully beneath the part to be removed.
Do not use any electrical or pneumatic servo screwdrivers or hammer drills.
Protective blanket required.
Protective goggles required.

K-2030-10+ Kukko Universal 2-Jaw and 3-Jaw Puller Set with Quick-Adjusting Pulling Jaws image 2

Related categories for K-2030-10+ Kukko Universal 2-Jaw and 3-Jaw Puller Set with Quick-Adjusting Pulling Jaws

Other Kukko Kits similar to K-2030-10+ Kukko Universal 2-Jaw and 3-Jaw Puller Set with Quick-Adjusting Pulling Jaws

KUKKO

KUKKO

KUKKO - The name for pullers


Bulk Order or Trade Enquiry? Contact us or give us a call on +44 (0)1709 527 269

Translate this page
FrançaisFrançais   EspañolEspañol   DeutschDeutsch   ItalianoItaliano   NederlandsNederlands
GBP EUR USD
Currency: GBP
Free UK Shipping German Pulling Tools Deep Groove Bearings Credit Application Form

Read our Privacy Policy Your access to and use of this Website is conditional on your acceptance of these Terms and Conditions of Use (H)
© Bearing King 2019, Unit 5, Stonerow Way, Parkgate, Rotherham, S60 1SG