Telephone: +44 (0)1709 527 269
Opening Hours: Monday to Friday (8.30am - 5.00pm)

Reference Code

Search by size


Use metric measurements only. See conversion chart.

Still can't find the part?

If you still can't find the part you need, contact us and we'll do all we can to locate it - just give us a call:
+44 (0)1709 527 269

Browse by category...

Due to Covid-19 deliveries may take longer than usual. Read our important update

K-20-15 Kukko Universal Puller Set with Separator

K-20-15 Kukko Universal Puller Set with Separator
K-20-15 Kukko In Stock
£909.00£1,090.80 inc. VATGBP £ | EUR € | USD $

For removing and separating ball bearings, roller bearings, inner rings and other flush parts.

7 in 1" kit in the tried-and-tested KUKKO-L-Boxx system.
The set facilitates the assembly of seven different puller models through the combination of separators, mechanical and hydraulic spindles, pulling jaws and extensions.
Pulling hook with quick adjusting capability quick adjust.
Jaw extensions.
Parallel pulling hooks in every position, even with full load.
Pulling hooks with infinitely variable adjustment on the cross-beam.
Hydraulic and mechanical pressure screw.
Milled thread treated with special coating.
The sharp blades enable flush parts to be removed where pulling jaws cannot be used.
Includes a pressure pad set for supporting the pressure spindle in a hollow shaft.
Instructions on the cover.
Secure storage in special foam.
Personal KUKKO-Chip-Code.

Practical package for universal use.
Easy and even pulling for particularly tight parts.
A manual adjustment knurl allows rapid loosening and adjusting of the extractor jaws on the cross-beam without using a wrench.
Variable reach with jaw extensions.
Optional conversion to various jaw types for mechanical use.
Turning the pulling hooks enables them to be used both internally and externally.
Suitable for pulling asymmetric workpieces.
Cross-beams with hexagonal profile for good grip.
Hydraulic spindle can be used for both cross-beams.
Spindle head band prevents the wrench from slipping off.
Almost all components available as replacement parts, time-saving order process thanks to numbering system.
Complete easy-to-manage package.
KUKKO-L-Boxx-System compatible with systems by all common manufacturers.

600-17 Pressure pad bricks
8-01 Long hydraulic spindle
15-2 Separators
18-2 Pulling device
20-1+ Universal 2-jaw puller with quick adjusting jaws
20-2+ Universal 2-jaw puller with quick adjusting jaws
1-192-P 2 quick adjusting jaws (pair)
2-302-P 2 quick adjusting jaws (pair)

How it Works
The puller must be positioned centrally for centre shafts. If the shaft is not sitting centrally, the parts can be removed asymmetrically with pullers with parallel pulling hooks.
Assembly instructions for the hydraulic spindle: 1. Loosen the side screw and unscrew the cap from the spindle body.
1. Loosen the side screw and unscrew the cap from the spindle body.
2. Screw the spindle body into the cross-beam from below until the spindle body sticks out of the cross-beam by approx. 60 mm.
3. Before use, check whether the pressure spindle is screwed far enough out of the cap so that the hydraulic piston is located in the initial position in the hydraulic cylinder.
4. Operating the upper spindle using the torque wrench will provide the force required for pulling.
5. After completing the removal process, the piston is reset to the initial position by turning the spindle in the opposite direction.

Safety Information
The pulling hooks' sliding parts must always sit stably and fully on the cross-beam.
If several parts have to be removed, always follow a step-by-step process. Do not remove several parts at the same time.
The pulling hooks' support surfaces must always be straight and sit fully beneath the part to be removed.
Do not use any electrical or pneumatic servo screwdrivers or hammer drills.
Protective blanket required.
Protective goggles required.

K-20-15 Kukko Universal Puller Set with Separator image 2

Related categories for K-20-15 Kukko Universal Puller Set with Separator

Other Kukko Kits similar to K-20-15 Kukko Universal Puller Set with Separator



KUKKO - The name for pullers

Bulk Order or Trade Enquiry? Contact us or give us a call on +44 (0)1709 527 269

Translate this page
FrançaisFrançais   EspañolEspañol   DeutschDeutsch   ItalianoItaliano   NederlandsNederlands
Currency: GBP
German Pulling Tools Deep Groove Bearings Credit Application Form

Read our Privacy Policy Your access to and use of this Website is conditional on your acceptance of these Terms and Conditions of Use
© Bearing King 2020, Unit 5, Northfield Business Park, Forge Way, Parkgate, Rotherham, S60 1SD