Find with reference code or description
Or search by measurements (mm)
FREE UK MAINLAND DELIVERY ON ORDERS OVER £100
Bearing King 3535 Taper Bushes 3535-70 Taper Locking Bush 70mm Bore

3535-70 Taper Locking Bush 70mm Bore

BKL Brand
3535-70 Taper Locking Bush 70mm Bore
3535-70 Taper Locking Bush 70mm Bore
In Stock
Taper lock bush suitable for pulleys and sprockets in the 3535 series
£43.49 INC.VAT
£36.24 EXC.VAT
Dimensions - d (inside diameter)70mm

Taper lock bush suitable for pulleys and sprockets in the 3535 series

Taper bushes are the most convenient and cost effective method of fixing components to a mating shaft without using any special tools

Bore dia: 70mm
Keyway width: 20mm
Keyway depth: 4.9mm
Shallow keyway depth: -

Screw tightening torque (Nm): 115
Screw size (BSW): 1/2 inch, hex, socket size: 10mm

Large end dia: 127mm
Bush length: 89mm

Mass: 5.0kg

To Install:
1. Clean shaft, bore and outside of bush, and bore of hub. Remove any oil, laquer or dirt, Place bush in hub and match half holes to make complete holes (each complete hole will be threaded on one side only).
2. Lightly oil thread and point of set screws, or thread and under head of cap screws. Place screws loosely in holes that are threaded on hub side.
3. Make sure bush is free in hub. slip assembly onto shaft and locate in the desired position.
4. Tighten screws alternately and evenly until all are pulled up tightly
5. Hammer against large end of bush using hammer and block or sleeve to avoid damage. Screws can now be turned a little more to the specified torque setting. repeat this alternate hammering and screw re-tightening until the specified torque is reached. Fill all holes with grease to exclude dirt.

To Remove:
1. Remove all screws. Lightly oil thread and point of set screws, or thread and under head of cap screws.
2. Insert screws into removed holes that are threaded on the bush side. In sizes where washers are found under screw heads, be sure to use the washers.
3. Tighten screws alternately until bush is loosened in the hub and then remove the complete assembly. If bush does not loosen immediately, tap on hub.

3535-70 Taper Locking Bush 70mm Bore image 2

BKL BrandBearing King offer a full range of BKL Brand products including ball, self-aligning, angular contact, cylindrical, needle and spherical bearings at highly competitive prices which are available for same or next day delivery

Related products Similar to 3535-70 Taper Locking Bush 70mm Bore

3535-2.1/4 Taper Locking Bush 2.1/4 inch Bore
BKL Brand
3535-2.1/4 Taper Locking Bush 2.1/4 inch Bore
Taper lock bush suitable for pulleys and sprockets in the 3535 series
Price Breaks / More Information
3535-2.5/16 Taper Locking Bush 2.5/16 inch Bore
BKL Brand
3535-2.5/16 Taper Locking Bush 2.5/16 inch Bore
Taper lock bush suitable for pulleys and sprockets in the 3535 series
Price Breaks / More Information
3535-38 Taper Locking Bush 38mm Bore
BKL Brand
3535-38 Taper Locking Bush 38mm Bore
Taper lock bush suitable for pulleys and sprockets in the 3535 series
Price Breaks / More Information
3535-2.1/2 Taper Locking Bush 2.1/2 inch Bore
BKL Brand
3535-2.1/2 Taper Locking Bush 2.1/2 inch Bore
Taper lock bush suitable for pulleys and sprockets in the 3535 series
Price Breaks / More Information