Telephone: +44 (0)1709 527 269
Opening Hours: Monday to Friday (8.30am - 5.00pm)
Search

Reference Code


Search by size

mm
mm
mm

Use metric measurements only. See conversion chart.


Still can't find the part?

If you still can't find the part you need, contact us and we'll do all we can to locate it - just give us a call:
+44 (0)1709 527 269


Browse by category...

30-20+S Kukko Universal 3-Jaw Puller with Narrow Quick Adjusting Jaws 150 x 260mm

30-20+S Kukko Universal 3-Jaw Puller with Narrow Quick Adjusting Jaws 150 x 260mm
30-20+S Kukko In Stock
£246.31£295.57 inc. VATGBP £ | EUR € | USD $
x

For removing bearings, gears, discs, etc. for tight or difficult-to-access spaces., leg length 150mm maximum pulling diameter 260mm

Description
Thin pulling hook with quick adjusting capability quick adjust.
Parallel pulling hooks in every position, even with full load.
Pulling hooks with infinitely variable adjustment on the cross-beam.
Optimal adjustment of the spindle to the shaft with 2-sided spindle tip (ball and tip).
Mechanical pressure screw.
Milled thread treated with special coating.
The three-arm design ensures that the load is distributed evenly and that the part to be removed is held securely.
If there is not adequate free space around the part to be removed, we recommend using a 2-jaw puller series 20+S for optimal force distribution.

Advantage
The thin pulling hooks are suitable for narrow, difficult-to-access locations.
A manual adjustment knurl allows rapid loosening and adjusting of the extractor jaws on the cross-beam without using a wrench.
Can be installed on various pulling hooks and variable reach thanks to jaw extensions.
Turning the pulling hooks enables them to be used both internally and externally.
Suitable for pulling asymmetric workpieces.
Spindle head band prevents the wrench from slipping off.
Almost all components available as replacement parts, time-saving order process thanks to numbering system.
Note: Pressure pads from series 600-17 are a good addition if the shaft is hollow and the spindle cannot be supported.

How it works
The part due to be removed (e.g. a gear, pulley or ball bearing) is gripped from the outside. Tightening of the pressure screw and the resulting pressure removes the part from the shaft.
The puller must be positioned centrally for centre shafts. If the shaft is not sitting centrally, the parts can be removed asymmetrically with pullers with parallel pulling hooks.

Spare part
621220 Mechanical pressure spindle.
2-150-S 3 pulling arms (set)
30-20-T3 3-jaw cross bar

Accessories
2-153-S 3 narrow, quick adjusting jaws (set)
2-303-S 3 narrow, quick adjusting jaws (set)

Safety information
The pulling hooks' sliding parts must always sit stably and fully on the cross-beam.
If several parts have to be removed, always follow a step-by-step process. Do not remove several parts at the same time.
The pulling hooks' support surfaces must always be straight and sit fully beneath the part to be removed.
Do not use any electrical or pneumatic servo screwdrivers or hammer drills.
Protective blanket required.
Protective goggles required.

30-20+S Kukko Universal 3-Jaw Puller with Narrow Quick Adjusting Jaws 150 x 260mm image 2

Related categories for 30-20+S Kukko Universal 3-Jaw Puller with Narrow Quick Adjusting Jaws 150 x 260mm

Other Universal 3-Jaw Puller with Narrow Quick Adjusting Jaws similar to 30-20+S Kukko Universal 3-Jaw Puller with Narrow Quick Adjusting Jaws 150 x 260mm

KUKKO

KUKKO

KUKKO - The name for pullers


Bulk Order or Trade Enquiry? Contact us or give us a call on +44 (0)1709 527 269

Translate this page
FrançaisFrançais   EspañolEspañol   DeutschDeutsch   ItalianoItaliano   NederlandsNederlands
GBP EUR USD
Currency: GBP
Free UK Shipping German Pulling Tools Deep Groove Bearings Credit Application Form

Read our Privacy Policy Your access to and use of this Website is conditional on your acceptance of these Terms and Conditions of Use (H)
© Bearing King 2019, Unit 5, Stonerow Way, Parkgate, Rotherham, S60 1SG