Find with reference code or description
Or search by measurements (mm)
FREE UK MAINLAND DELIVERY ON ORDERS OVER £100
Bearing King 2517 Taper Bushes 2517-22 Taper Locking Bush 22mm Bore

2517-22 Taper Locking Bush 22mm Bore

BKL Brand
2517-22 Taper Locking Bush 22mm Bore
2517-22 Taper Locking Bush 22mm Bore
In Stock
Taper lock bush suitable for pulleys and sprockets in the 2517 series
£15.23 INC.VAT
£12.69 EXC.VAT
Dimensions - d (inside diameter)22mm

Taper lock bush suitable for pulleys and sprockets in the 2517 series

Taper bushes are the most convenient and cost effective method of fixing components to a mating shaft without using any special tools. Taper bushes are pre-machined with the required bore & keyway size and are supplied complete with locking set screws, thus making savings in time and cost on any machining process.

Bore dia: 22mm
Keyway width: 6mm
Keyway depth: 2.8mm
Shallow keyway depth: -

Screw tightening torque (Nm): 50
Screw size (BSW): 1/2 inch, hex, socket size: 6mm

Large end dia: 85.5mm
Bush length: 44.5mm

Mass: 1.5kg

To Install:
1. Clean shaft, bore and outside of bush, and bore of hub. Remove any oil, laquer or dirt, Place bush in hub and match half holes to make complete holes (each complete hole will be threaded on one side only).
2. Lightly oil thread and point of set screws, or thread and under head of cap screws. Place screws loosely in holes that are threaded on hub side.
3. Make sure bush is free in hub. slip assembly onto shaft and locate in the desired position.
4. Tighten screws alternately and evenly until all are pulled up tightly
5. Hammer against large end of bush using hammer and block or sleeve to avoid damage. Screws can now be turned a little more to the specified torque setting. repeat this alternate hammering and screw re-tightening until the specified torque is reached. Fill all holes with grease to exclude dirt.

To Remove:
1. Remove all screws. Lightly oil thread and point of set screws, or thread and under head of cap screws.
2. Insert screws into removed holes that are threaded on the bush side. In sizes where washers are found under screw heads, be sure to use the washers.
3. Tighten screws alternately until bush is loosened in the hub and then remove the complete assembly. If bush does not loosen immediately, tap on hub.

2517-22 Taper Locking Bush 22mm Bore image 2

BKL BrandBearing King offer a full range of BKL Brand products including ball, self-aligning, angular contact, cylindrical, needle and spherical bearings at highly competitive prices which are available for same or next day delivery

Related products Similar to 2517-22 Taper Locking Bush 22mm Bore

2517-50 Taper Locking Bush 50mm Bore
BKL Brand
2517-50 Taper Locking Bush 50mm Bore
Taper lock bush suitable for pulleys and sprockets in the 2517 series
Price Breaks / More Information
2517-32 Taper Locking Bush 32mm Bore
BKL Brand
2517-32 Taper Locking Bush 32mm Bore
Taper lock bush suitable for pulleys and sprockets in the 2517 series
Price Breaks / More Information
2517-2.3/16 Taper Locking Bush 2.3/16 inch Bore
BKL Brand
2517-2.3/16 Taper Locking Bush 2.3/16 inch Bore
Taper lock bush suitable for pulleys and sprockets in the 2517 series
Price Breaks / More Information
2517-45 Taper Locking Bush 45mm Bore
BKL Brand
2517-45 Taper Locking Bush 45mm Bore
Taper lock bush suitable for pulleys and sprockets in the 2517 series
Price Breaks / More Information